• This gateway can read data from your Metasys N2 devices and publish it as BACnet MSTP data.
• It can also write to the Metasys N2 devices.
• This gateway can also do the reverse, read BACnet MSTP data and publish it as Metasys N2 data.
• It can also write to the BACnet MSTP devices.

In summary, this gateway can act as:

• Master on the Metasys N2 network: Hence it is capable of reading data from the various Modbus slave devices and writing data to them if required.
• Slave on the Metasys N2 network: You can use the gateway in this mode if you have a Metasys N2 master on the network which would be reading data from the gateway.
• Master on the BACnet MSTP network: Hence it is capable of reading data from the various BACnet MSTP devices and writing data to them if required.
• Slave on the BACnet MSTP network: The gateway can be configured to be a server of data values; hence another BACnet MSTP client can read data from the gateway and write data into the gateway.

 QuickServer Key Features:

• BACnet Testing Laboratory (BTL) Mark
• Ability to interface up to 250 points of common BAS protocols
• Multi-configuration capability; specific configurations selectable via DIP switches or software
• Flat panel mount standard, DIN rail mount option
• DIP switches to select baud rate or node ID on the fly

BACnet MS/TP driver:

• Driver type: Client or Server
• Data Link layer: MS/TP master (Clause 9), baud rate up to 38.4 Kbps, MS/TP slave (Clause 9), baud rate up to 38.4 Kbps
• Connection type: RS-485 (two wire, half duplex)
• Baud rates: 9600, 38400, 76800
• BACnet COV support for fast data communication while reducing traffic over a BACnet network
• Data types supported:
  • AI - Analog Input Object
  • AO - Analog Output Object
  • AV - Analog Value Object
  • BI - Binary Input Object
  • BO - Binary Output Object
  • BV - Binary Value Object
  • MI - Multi-state Input Object
  • MO - Multi-state Output Object
  • MV - Multi-state Value Object

JCI Metasys N2 driver:

• Supports communication with following devices or classes of devices when acting as a Client
  • N2OPEN-compliant devices
  • VMA 1400 series
  • DX9100 and XT9100
• Driver type: Client or Server
• Connection type: RS-485 (two wire, half duplex)
• Baud rates: 9600
• Devices tested:
  • UNT
  • VMA1410,
  • VMA1420
  • DX9100 with XT9100 extension
  • NCM (FieldServer as N2Open server)
  • VAV
  • AHU
  • VND

• Metasys is a trademark of Johnson Controls
• BACnet is a trademark of ASHRAE

How to configure the FieldServer gateway?

-We will configure the gateway for you based on your requirement and support you during commissioning of the gateway, so you do not  have to worry about configuring the FieldServer gateway.

-However, it is very helpful to know how to configure the devices. All the required tools and supporting product manuals with be provided completely free of cost with your purchase.

-Configuration of the FieldServer is done using a '.csv' file. This file can be edited using any text editor (example Microsoft excel).

-In this file we need to enter information for the Client and Server side interfaces of the FieldServer. This includes but is not limited to:

                Node ids of the slave devices

                IP addresses/device address of the slave devices

                Baud rate, parity, stop bits for serial communication

                Scan rates

- And finally we need to create an internal mapping that would map each data value read on the client side to a data value on the server side.

-For detailed information on configuration please get in touch with us and review the configuration manual on top of this page